AEG 34602G-D Bedienungsanleitung Seite 1

AUS ERFAHRUNG GUT21601C/ 34611C/ 35601C/ 35610C34602G/ 35600G/ 35601G/ 35604GGas hobTable de cuissonKochmuldeGaskookplaatPiano di cotturaOperating and

10Guarantee ConditionsAEG offer the following guarantee to the first purchaser of this appliance.1. The guarantee is valid for 12 months commencing wh

11Overall dimensionsWidth: 580 mm.Depth: 500 mm.Cut out dimensionsWidth: 550 mm.Depth: 470 mm.Supply ConnectionsGas: RC 1/2 inch (1/2 inch male) Rear

12Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

13650 mm400 mm400 mm100 mm50 mm50 mm55 mm600 mm700 mm400 mm100 mm400 mm50 mm55 mm50 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOO

14A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed

1555047058050055 min.FO 2291Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the ho

16ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unitwith doorProper arrangements must be taken indesigning the

17Fitting the hob to the worktopBefore fitting the hob into the cut out, a sealing gasket supplied with the hob must be fittedto the edge of the cut o

18Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

19Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity

2 Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer C

20Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

21A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on W (Ohms) x 1 scale andadjust zero if necessary. Test leads fro

22Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

23CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting. Todo this, follow the procedure below.1)

24Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can beconverted for use with buta

3l When using the hob for a long period of time, the ventilation should be improved, byopening a window or increasing the extractor speed.l Do not use

4This appliance is manufactured according to the following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition.

51. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn

6Hob burnersTo light a burner:l turn the relevant control knob anticlockwise to the maximum position, then push it down toignite the burner. Upon, ign

7Before any maintenance or cleaning can be carried out, you must DISCONNECT thehob from the electricity supply.The hob is best cleaned whilst it is st

8Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.

9Service and Spare PartsWhen you contact the Service Force Centre, they will need the following information:1. Your name, address and post code.2. You