AEG L89495FL Bedienungsanleitung

L 89495 FL EN User manual

4.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.4.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3

• Before you press the Start/Pause but-ton 4 : the appliance cannot start.• After you press the Start/Pause button4 , all the buttons and the pro-gram

ProgrammeTemperature rangeType of load and soilMaximum load, Maximum spinAnti-Allergie60°CWhite cotton items. This programme removesmicro-organisms th

Programme options compatibilityProgramme 1) 2)

6. CONSUMPTION VALUESAt programme start the display shows the duration programme for the max-imum load capacity.During the washing phase the programme

2.Put a small quantity of detergent inthe main wash compartment of thedetergent dispenser. Set and start aprogramme for cotton at the highesttemperatu

The detergent compartment for the washing phase.If you use a liquid detergent, put it immediately before you startthe programme.Liquid additives compa

4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or thickliquid detergents.– Do not put more liq

2.Press button 4 again. The washingprogramme continues.8.7 Cancel a programme1.Press button 1 to cancel the pro-gramme and to deactivate the appli-anc

• Do not wash together white and col-oured items.• Some coloured items can discolourwith the first wash. We recommendthat you wash them separately for

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

Do this separately from the laundrywash.10.2 External cleaningClean the appliance only with soap andwarm water. Fully dry all the surfaces.CAUTION!Do

3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the dispe

3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

11. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solution You did not remove thepackaging and/or thetransit bolts.Remove the packaging and/orthe transit bolts. Refer

To open the door, proceed as follows:1. Press the button to switch the appliance off.2. Disconnect the mains plug from the mains socket.3. Open the f

14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

ENGLISH 29

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

30www.aeg.com

ENGLISH 31

www.aeg.com/shop132910680-A-432013

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

3. PRODUCT DESCRIPTION1 2 3 8956741011121Worktop2Detergent dispenser3Control panel4Door handle5Rating plate6Drain pump7Feet for the appliance level8Wa

4. CONTROL PANEL1 2 3456789101On/Off button ( Auto Off)2Programme knob3Display4Start Pause button 5Delay start button 6Time save button 7Extra rinse b

The display shows:AThe temperature of the set programmeCold waterBThe spin speed of the set programmeNo Spin symbol1)Rinse Hold symbol1) Only availabl

• The delay startWhen you press the delay start button, the display showsthe delay start time.•Alarm codesIf the appliance has a malfunction, the disp