AEG FFE63806PM Bedienungsanleitung

USER MANUALEN User ManualDishwasherFFE63806PM

Programme 1)Water(l)Energy(kWh)Duration(min)P7 12 - 14 0.8 - 1.0 82 - 92P8 12 - 13 1.1 - 1.3 230 - 250P9 4 0.1 14P0 10 0.86 60 - 701) The pressure and

6.2 The water softenerThe water softener removes mineralsfrom the water supply, which would havea negative effect on the washing resultsand on the app

the notification for refilling rinse aid.However, for best drying performance,always use rinse aid.If standard detergent or multi-tabletswithout rinse

CAUTION!Do not try to close theappliance door within 2minutes after automaticopening. This can causedamage to the appliance.If, afterwards, the door i

automatically activated in next cycles.This configuration can be changed at anytime.Every time isactivated, XtraDry is off andneeds to be chosenmanu

3. Fill the salt container with dishwashersalt (until it is full).4. Carefully shake the funnel by itshandle to get the last granulesinside.5. Remove

CAUTION!Make sure that items do notstick out of the basket frameas it can cause damage tothe items and the ComfortLift mechanism.The Comfort Lift mech

approximately 3 seconds and thenshows the programme duration.• To select the MyFavouriteprogramme, press .• The indicators of the optionsrelated to t

10. HINTS AND TIPS10.1 GeneralFollow the hints below to ensure optimalcleaning and drying results in daily useand to help you protect the environment.

10.5 Before starting aprogrammeBefore you start the selectedprogramme, make sure that:• The filters are clean and correctlyinstalled.• The cap of the

CONTENTS1. SAFETY INFORMATION...22. SAFETY INSTRUCTIONS...

5. Make sure that there are no residuesof food or soil in or around the edgeof the sump.6. Put back in place the flat filter (A).Make sure that it is

11.3 External cleaning• Clean the appliance with a moist softcloth.• Only use neutral detergents.• Do not use abrasive products,abrasive cleaning pads

Problem and alarm code Possible cause and solutionThe appliance does not fillwith water.The display shows or .• Make sure that the water tap is open

Refer to "Before first use", "Daily use", or "Hints andtips" for other possiblecauses.Once you have checked the applianc

Problem Possible cause and solutionTraces of rust on cutlery. • There is too much salt in the water used for washing.Refer to "The water softener

Water supply pressure bar (minimum and maximum) 0.5 - 8MPa (minimum and maximum) 0.05 - 0.8Water supplyCold water or hot water 2)max 60 °CCapacity Pla

www.aeg.com26

ENGLISH 27

www.aeg.com/shop117868390-A-242018

manufacturer is not responsible for any injuries ordamages that are the result of incorrect installation orusage. Always keep the instructions in a sa

• If the supply cord is damaged, it must be replaced bythe manufacturer, its Authorised Service Centre orsimilarly qualified persons in order to avoid

fuse, use only a 13 A ASTA (BS 1362)fuse.2.3 Water connection• Do not cause damage to the waterhoses.• Before connection to new pipes,pipes not used f

3. PRODUCT DESCRIPTION6510 781413121115 342911Worktop2Top spray arm3Upper spray arm4Lower spray arm5Filters6Rating plate7Salt container8Air vent9Rinse

4. CONTROL PANEL1234567891On/off button2Display3Program button4Delay button5MyFavourite button6TimeSaver button7XtraDry button8ExtraHygiene button9Ind

Programme Degree of soilType of loadProgramme phases OptionsP6 3)• Mixed soil• Crockery, cutlery,pots and pans• Prewash• Wash 50 °C and65 °C• Rinses•

Programme Degree of soilType of loadProgramme phases OptionsP0 10)• No load • Self-cleaning 1) This programme offers the most efficient use of water