AEG PE8038-M Spezifikationen Seite 1

Espresso coffee machineOperating and Installation InstructionsPE 8038-m/a - PE 8039-m

11 • Pour approximately 200 g of coffee beans into the container on the top as shown in the figure. • push the machine back into t

12 INITIAL START-UP • Ensuring the water reservoir is full, turn the steam/water knob anti clockwise as shown above. • Switch the coffee mac

13 • When the water is flowing close the steam/water knob by turning clockwise. (if necessary, repeat the …….. process several times) • When

14 • All the LEDs will briefly illuminate to indicate the factory values have been reset. N.B.: The standard values only concern the quantity of w

15 • Pull the coffeee machine forward from it’s hausing by sliding it along it’s telescopic runners . • Turning the proper adjusting k

16 • Once powered and inserted into the cabinet, the machine is in stand-by mode: this will be signaled by the on/off LED blinking. • Keep the

17 6. DRAWER • This machine is be provided with a well-equipped drawer PES 8038-m, This drawer has a lot of useful compartments: - a large compa

18 • Insert the filter holder under the coffee measuring device by pressing the button briefly. The programmed quantity of ground coffee will auto

19 • Lock the filter holder firmly turning the handle from left to right. • If preparing espresso use the special cup rack inserting it

20 • Press the coffee control as shown coffee will be dispensed into the cup(s) Remove the filter holder from the ring nut and dispose of the used

3 CONTENTS 1. Description of the coffee machine 2. Description of the control panel: touch control 3. Safety instructions 4. Instructions for

21 • This machine is also designed to operate with coffee pods, these are single portions of roasted coffee • Procede as with ground coffee. Aft

22 8. HOT WATER • The steam/water pipe can be moved to the back of the cabinet when not in use Use to allow easy access to the filter holder

23 • Close the steam/water knob again. 9. STEAM HEATING LIQUIDS • Press the steam control once. Both the steam and water temperature indi

24 • Place a jug with the liquid to be heated under the steam nozzle and turn the steam knob in anticlockwise as shawn. • Move the jug arou

25 10. PROGRAMMING THE QUANTITY OF GROUND COFFEE • This espresso machine has already been calibrated in factory to dispense the ideal measure of gr

26 11. PROGRAMMING THE QUANTITY OF COFFEE POURED IN THE CUP • The quantity of coffee can be adjusted as desired. Select the coffee programme req

27 • When the desired quantity of coffee has been dispensed press the control again and the coffee measure will be stored automatically. 12. P

28 • Release the control when the water starts to flow; then, once the desired quantity of water is obteined press the control again and this meas

29 VIENNESE CAPPUCCINO This variation is the result of the age-old Austrian tradition. Prepare a 'weak' espresso on the machine for 30-35 s

30 14. CLEANING OUTER PARTS • Clean the stainless stell parts of the machine with a soft cloth without using aggressive detergents. Never use any

4 1. DESCRIPTION OF THE COFFEE MACHINE 1. Filter holder ring nut 2. Steam/water nozzle 3. Coffee press 4. Coffee Grinder button 5. Coffee m

31 FILTER – FILTER-HOLDER – LOCKING NUT • Always keep filters, filter-holder and locking nut clean. Any coffee residue can alter the taste of the ne

32 • Fill up the water reservoir with 1.5 litres of water adding half a glass of vinegar or citric acid. • Carry out the same operations as preparin

33 ELECTRICAL CONNECTION • Fix the power cable onto the left side of the cabinet using one of the self-threading screws of the equipment and th

34 • Connect the power cable as it is shown in the figure. This machine is designed for a single phase voltage of 230V The power supply requires on

35 for the different possible measures. They should be used to compensate for the internal width of the compartment, leading to a width of 560/570 mm

36 • Slide the machine into the cabinet untill the “click” indicates that it is locked into Position. COMPONENTS FOR INSTALLING THE DR

37 INSTALLING MACHINE + DRAWER • Lay the fixing base of the drawer onto the proper shelf of the cabinet. • Insert the side plate

38 • Fix the base plate inserting 4 self-threading screws into the 4 fore holes of the plate. Then assemble the 2 slides with the remaining 10 s

39 • Four side plates (two being 2 mm thick and two 1 mm thick) are provided together with the machine, to compensate for the different possible

40 • Insert the machine coupling its slides with those already mounted onto the cabinet’s sides and slide it into the cabinet to the stops unt

5 2. DESCRIPTION OF THE CONTROL PANEL: TOUCH CONTROLS 1. Water temperature indicator 2. ON/stand-by indicator 3. Coffee indicator 4. Water in

41 17. TECHNICAL SPECIFICATIONS As regards the general dimensions of the machine, please see the fig. D • Width 594 mm •

42 18. DECLARATION OF GUARANTEE TERMS SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG S

43 GUARANTEE CONDITIONS AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencin

AEG Hausgeräte GmbHPostfach 1036D-90327 NürnbergHttp://www.aeg.hausgeraete.de© Copyright by AEG04501150

6 3. SAFETY Please read this instruction book before using thè appliance and retain for future reference. These warnings are provided in the interest

7 FOR INSTALLATION AND SERVICING Keep this instruction manual together with the machine for any future reference. If the machine is sold or transfer

8 The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed

9 Hardness of water: • Before filling up the water reservoir, make sure that the decalcifying Brita filter has been soaked in cold water for at least

10 • Ensure the mains ON/OFF switch(at rear) is ON • push the machine back into the housing untill a “CLICK” can be heard. This indicate that th