L 87480 FLL 87680 FLEN User manual
KThe extra rinse symbol comes on when this function is acti-vated.The value shows the total number of the rinses.The indicator bar is fully filled whe
5.10 Temperature button 10Press button 10 to change the defaulttemperature. When the display shows - -, the appliance does not heat the wa-ter.5.11 Ac
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsSynthetics60° - ColdSynthetic or mixed fabricitems with normal soil.max.
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsRinse0°All fabricsmax. load 8 kgOne rinsewith addi-tiveSpin phaseSPIN RE
Steam - RefreshThis cycle removes odours from thelaundry.Steam does not remove animalodours.Cotton and syntheticitemsup to 1.5Kg Steam - AnticreaseTh
Programmes Load(Kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approxi-mate pro-grammeduration(minutes)Remainingmoisture(%)1)Cottons 40°C8 0.90
9.1 Loading the laundry1.Open the appliance door.2.Put the laundry in the drum, oneitem at a time. Shake the items be-fore you put them in the applian
Always obey the instructions that you find on the packaging of the de-tergent products.Check the position of the flap1.Pull out the detergent dispense
4.To change the temperature and/orthe spin speed, press the relatedbuttons.5.Set the available functions.6.Press button 4 to start the pro-gramme. The
9.10 At the end of theprogramme• The appliance stops automatically.• The acoustic signals operate.•In the display comes on.• The indicator of the Sta
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
10.3 Detergents and additives• Only use detergents and additivesspecially made for washing machines.• Do not mix different types of deter-gents.• To h
• Use a correct quantity of powder de-tergent with biological properties.After each wash, keep the door open fora while to prevent mould and to let un
5.Clean the dispenser recess with abrush.6.Put back the dispenser in the recess.11.7 Drain pumpRegularly examine the drainpump and make sure that it i
125.When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and again until no morewater fl
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai
2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from
127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for
13.4 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co
Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t
• If the end of the drain hose is this (seethe drawing), you can push it directlyinto the stand pipe.Without the plastic hose guide.• To a sink spigot
13.6 In the interest of the environment• Connect the appliance to the FOULsystem for the drain water. The sew-age works keeps the drain water forthe t
ENGLISH 35
www.aeg.com/shop132939731-A-382012
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
mains plug, use a 13 amp ASTA (BS1362) fuse.•This appliance complies with theE.E.C. Directives.Water connection• Make sure not to cause damage to thew
Level of protection against ingress of solid parti-cles and moisture ensured by the protective cover,except where the low voltage equipment has noprot
4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
EThe detergent overdosing comes on at the end of the cy-cle when the appliance detects too much detergent.FYou cannot open the appliance door when the
Kommentare zu diesen Handbüchern