AEG L76485FL Bedienungsanleitung

L 76485 FLL 76487 FLEN User manual

Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11

ProgrammeTemperatureType of loadmax. weight ofloadCycle description FunctionsKoke-/Kulørt +Forvask95° - ColdWhite and colouredcotton with heavysoil.ma

ProgrammeTemperatureType of loadmax. weight ofloadCycle description FunctionsSkyllingColdHand washingitems.RinsesLong spinSPIN REDUC-TIONRINSE HOLDEXT

STEAM PROGRAMMESProgramme1)Type of load Max. loadDamp OppfriskningThis cycle removes odours fromthe laundry.Steam does not removeanimal odours.Cotton

The data of this table are approximate. Different causes can change the da-ta: the quantity and type of laundry, the water and ambient temperature.Pro

5.Use the correct quantity of deter-gent and additives.6.Set and start the correct programmefor the type of laundry and soil.9.1 Loading the laundry1.

Flap for powder or liquid detergentTurn it (up or down) in the correct position to use powder or liq-uid detergent.Always obey the instructions that y

9.3 Setting and starting aprogramme1.Turn the programme knob. The rela-ted programme indicator comes on.2.The indicator of button 4 flasheswith red co

If the temperature and level ofthe water in the drum are toohigh, the door lock symbol stayson and you cannot open thedoor. To open the door do theste

– Underwired bras.– Use a washing bag to wash smallitems.• A very small load can cause balanceproblems with the spin phase. If thisoccurs, adjust manu

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

find on the packaging of the manufactur-er.Do this separately from the laundrywash.11.2 External cleaningClean the appliance only with soap andwarm wa

3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the dispe

3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l

To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif

12. TROUBLESHOOTINGThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the ta

Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T

Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai

2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from

127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f

WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

ENGLISH 33

34www.aeg.com

ENGLISH 35

www.aeg.com/shop132916250-A-502012

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 8 kgSpin speed Maximum 1400 rpm1

4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th