L 75480 WD EN User manual
D • The programme time (washing and/or drying phase)When the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you pr
5.10 Spin button 9Press this button to:• Decrease the maximum speed of thespin phase when you set a pro-gramme.The display shows only the spinspeeds a
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsSyntheticaSynthetics60° - ColdSynthetic or mixedfabric items withnormal lev
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsDRYING PROGRAMMESWolWoolWool itemsmax. 1 kgTimed drying onlySyntheticaSynth
7) Set this programme to decrease the time and the consumption of energy and water.8) Cotton Energy Saving programme » at 60°C with a load of 8 kg is
6.2 Programmes for timed dryingDegree of drying Type of fabricLoad(Kg)Spinspeed(rpm)Sugges-ted times(mins)Extra dryFor towelling mate-rialsCotton and
Programme Energy con-sumption(KWh)Water con-sumption(litres)Programmeduration(minutes)Cottons 60° 1.60 72For the du-ration of thepro-grammes,please re
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a
Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge
5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The drain pump can operate fora short time when the appliancefills water.The
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
• The door lock symbol goes off.•Press button 1 to deactivate the ap-pliance. After five minutes from theend of the programme, the energysaving functi
The display shows a minimum timevalue.Set time value• Each time you press this button thetime value increases by 5 minutes.• After some seconds the ti
The time value on the display is theduration of the washing + drying cy-cles calculated on a default load size.•Press button 4 to start the pro-gramme
• To clean the drain filter.• After the drying phase, clean the emp-ty drum, the gasket and the door witha wet cloth.To remove the fluff inside the dr
Equivalent scales measure the waterhardness:• German degrees (°dH).• French degrees (°TH).• mmol/l (millimol for each litre - inter-national unit for
13. CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.13.1 DescalingThe water we use contains limescale. If i
13.6 Detergent dispenserTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquidadditive compartment.4.
To clean the drain pump:1.Open the drain pump door.2.Pull the flap out to remove it.3.Put a container below the recess ofthe drain pump to collect the
129.Clean the filter under the water tapand put it back in the pump into thespecial guides.10.Make sure that you tighten correctlythe filter to preven
Put the drainage duct back and close thedrain pump flap.When you drain the water with the emer-gency drain procedure, you must acti-vate again the dra
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
Problem Possible cause Possible solutionThe appliancedoes not drain thewater.The water drain hose isdamaged.Make sure that the water drainhose has no
Problem Possible cause Possible solution Leakages from the drainpump.Make sure that the drain pumpfilter is tight. The water drain hose isdamaged.Ma
Problem Possible cause Possible solution You have set a wrongdryness level or dryingtime.Set additional drying time.There is a bigquantity of fluff i
2.Remove the cardboard top.3.Remove the polystyrene packagingmaterials.4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from
127.Remove the polystyrene protectionfrom the bottom.8.Pull up the appliance in vertical po-sition.9.Remove the power supply cable andthe drain hose f
WARNING!Remove all the packaging andthe transit bolts before you installthe appliance.We recommend that you keepthe packaging and the transitbolts for
• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
16. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a
ENGLISH 39
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
www.aeg.com/shop132924922-A-452013
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove the door catch to preventchildren and pets to get cl
4. PRODUCT DESCRIPTION1 2 3 8956741011121Worktop2Detergent dispenser3Control panel4Door handle5Rating plate6Drain pump7Feet for the appliance level8Wa
4.2 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra
Kommentare zu diesen Handbüchern